Search found 8 matches
- Thu Jul 19, 2018 3:10 pm
- Forum: Basics & Tutorials
- Topic: Question about driving the LED in tutorial 6
- Replies: 1
- Views: 4677
Question about driving the LED in tutorial 6
Hi there. In tutorial 6 the STS port is connected to a red LED, with a 220 Ohm current limit resistor. I have two questions for that setup, which I hope someone can clarify. ⋅ Why 220 Ohm? The docs says 370? Assuming a voltage drop of 2V across the led (pretty standard for red leds), and ...
- Thu Jul 19, 2018 2:35 pm
- Forum: Basics & Tutorials
- Topic: RTK receivers with Arduino (tutorial 6)
- Replies: 3
- Views: 6096
Re: RTK receivers with Arduino (tutorial 6)
Hi Francis I know this is a little late, but just wanted to point out that another reason the bluetooth module is used, may be because the NavSpark modules are all 3.3V LVTTL, and the Arduino is 5V. So, the Arduino can use input from the NavSpark directly, but would fry the chip, it it tried to outp...
- Thu Jul 19, 2018 2:27 pm
- Forum: New User Posting
- Topic: Activation of login?
- Replies: 2
- Views: 521
Re: Activation of login?
Thanks! And, no problem, I just wanted to respond to a post somewhere else in the forum, and was unable.
Thanks!
Kind regards
Mads
Thanks!
Kind regards
Mads
- Wed Jul 18, 2018 3:21 pm
- Forum: New User Posting
- Topic: Activation of login?
- Replies: 2
- Views: 521
Activation of login?
Hi there
Although I made my first post in march, I can still not post in other forums than this. Moderators, could you please "do something" .
Kind regards,
Mads
Although I made my first post in march, I can still not post in other forums than this. Moderators, could you please "do something" .
Kind regards,
Mads
- Wed Jul 18, 2018 1:38 am
- Forum: New User Posting
- Topic: My Autonomous Agricultural Robot with Navpark NS-HP-BD.
- Replies: 2
- Views: 629
Re: My Autonomous Agricultural Robot with Navpark NS-HP-BD.
Amazing! Great job.
Do you have schematics for it? Just curious...
Kind regards
Mads
Do you have schematics for it? Just curious...
Kind regards
Mads
- Thu Apr 26, 2018 3:06 pm
- Forum: New User Posting
- Topic: How to "stay" in Fix RTK mode with NS-HP-GL
- Replies: 5
- Views: 1331
Re: How to "stay" in Fix RTK mode with NS-HP-GL
Hi,I think your Triband antena is good enough. :) So in my experience use NS-HP-BD to keep FIX RTK run for for lonng time, You need to make sure everything is not interrupted : Signal quality >= 38db , dont touch or put anything above antena. You can improve signal by put antena on a iron ground pl...
- Wed Apr 25, 2018 5:05 pm
- Forum: New User Posting
- Topic: How to "stay" in Fix RTK mode with NS-HP-GL
- Replies: 5
- Views: 1331
Re: How to "stay" in Fix RTK mode with NS-HP-GL
MOUSE and CAT wrote:Hi , which antena you are using for system ?
I am using this http://navspark.mybigcommerce.com/tri-b ... e-antenna/ - should be ok, not?
Kind regards
- Wed Apr 25, 2018 2:38 am
- Forum: New User Posting
- Topic: How to "stay" in Fix RTK mode with NS-HP-GL
- Replies: 5
- Views: 1331
How to "stay" in Fix RTK mode with NS-HP-GL
Hi there New user. I am trying out the base+rover combo with a NS-HP-GL as base (survey, 60 seconds) and a NS-HP-GL (5Hz) as rover. Simple setup, like userguide. When I start the "rover" after the base have settled, it is completely random how quickly it goes into Fix RTK. Sometimes it tak...